How to Make Rubber Stamps

by Kelsey Hofmeister

Supplies

  • Speedball Linoleum cutter
  • Carving block
  • Pencil
  • Paper
  • Ink pad
  • Wood block
  • E6000 glue
  • Handle (optional)
  • Instructions

    Step 1

    THESE MAKE THE BEST PRESENTS EVER. EVARR.

    Step 2

    First, sketch a few different designs. I used the end of the speedball cutter to get a good circle.

    Step 3

    Draw over the design so that the lines are thick-- thin lines do not transfer well.

    Step 4

    Place the rubber on the design and press. Some people use tracing paper to transfer the design, but they're just silly. You don't need it. (The real reason may be that I'm cheap, but hey, this works.)

    Step 5

    So maybe this isn't the best way to transfer..

    Step 6

    ..but whatevs, just draw over it! Some people use permanent marker or pen so that the image is easier to see. But, again, they're just silly. Stick with me, kid.

    Step 7

    I found this cutter on amazon, it came with 5 different cutting shapes. You can quickly change out blades and store them inside the cutter.

    Step 8

    Start with the smallest blade. Anything you cut away will not pick up ink. Cut away the sides of any big sections.

    Step 9

    Next, cut away the middle section. You can change to a bigger blade depending on how big the section is.

    Step 10

    When cutting the edge outline, switch to a deeper cutter (number 2 or 3). Try to not stop when you are making a cut to make it look clean.

    Step 11

    Switch to a scooper blade when you need to cut out huge sections. Yes, scooper blade. It looks like a scooper. Don't make fun of me.

    Step 12

    Cut that baby off! You could do it on your lap, or use a hard surface. I'll let your common sense decide.

    Step 13

    When you're ready to test it, stamp it on an ink pad and try it out. You can cut away any extra marks you don't want.

    Step 14

    Continue stamping and removing any unwanted marks. You can use tweezers to remove small pieces, like you can see oh so clearly in this pic. Nice work iPhone.

    Step 15

    Try not to cut more than necessary. The smallest cut can make you super frustrated with the result.

    Step 16

    Next, make a wood backing. You want it to be wood since it will distribute the pressure to the whole stamp without wearing down or cracking. Use a jigsaw and a cheetah print pencil to cut the blocks.

    Step 17

    This part is optional, but I think they look cute with the stamp. I found these at Menards, but you can find pretty cute ones at Joann's or Anthropologie.

    Step 18

    Drill a hole through the center of the block to fit the the treads of the screw. You don't need a mill to do this. Don't ask me how or why I have access to one.

    Step 19

    Make a counter sink that will fit the screw's head. This side will have the stamp, so the screw's head can't be in the way.

    Step 20

    You may need to take some material off of the screw's head if it doesn't fit well. And don't wear jewelry when you work with tools...this picture is deceiving you...

    Step 21

    I stained the blocks and then dry brushed with prettyshinymetallicsparkly gold. The best part of typing that was that my iPhone autocorrected gold to hold. Eh?

    Step 22

    Insert the screw and twist the handle on the other end. Don't screw it up. Heh heh. Heh.

    Step 23

    Apply a small layer of glue on both the rubber and the block. You could other kinds, but this one will really make it last. Quick, find all the pics in this guide with my finger on the top.

    Step 24

    Center the stamp on the block and press firmly.

    Step 25

    Here are all the ones I made!

    Step 26

    For these, I found small boxes at Joann's for a dollar each and stamped the monogram on top. Put a little tissue paper in it and...

    Step 27

    Voila!