How to Make Beer Bottle Cap Coasters

The perfect gift for the beer lover in your life!

8.9k Views 545 Likes 1 Comment
How to Make Beer Bottle Cap Coasters
21 Steps
Supplies
Embed
1
Gather your supplies! A lot of them are optional because they were used for the box the coasters sit in.

Gather your supplies! A lot of them are optional because they were used for the box the coasters sit in.

2

Pick out 9 bottle caps for each coaster

Recommended For You
3
Take one cork coaster and one chipboard piece...

Take one cork coaster and one chipboard piece...

4
And brush a good amount of tacky glue all over the chipboard

And brush a good amount of tacky glue all over the chipboard

5
Then press the chipboard in the center of the coaster and secure with clothespins.

Then press the chipboard in the center of the coaster and secure with clothespins.

6
I added even more clothespins to securely seal the cork to chipboard.

I added even more clothespins to securely seal the cork to chipboard.

7

You can use clamps, books, or whatever else you have laying around the house. I had clothespins so that's what I used

8

VERY IMPORTANT: let them dry for AT LEAST and hour or else they will peel apart in the next step

9
CAREFULLY trim the excess cork with scissors

CAREFULLY trim the excess cork with scissors

10
Lay out your caps in different patterns on the coasters until you like the way they look. Take a picture so you don't forget and use it as reference when gluing them down.

Lay out your caps in different patterns on the coasters until you like the way they look. Take a picture so you don't forget and use it as reference when gluing them down.

11
Clear off your coaster, heat up that glue gun and carefully squeeze glue around the INSIDE of the cap. The cap will get hot so be careful!

Clear off your coaster, heat up that glue gun and carefully squeeze glue around the INSIDE of the cap. The cap will get hot so be careful!

12
Begin placing caps on coasters. I found it easiest to place the center cap first, then the other caps around it.

Begin placing caps on coasters. I found it easiest to place the center cap first, then the other caps around it.

13
All glued down. If a part of a cap sticks off the edge just take pliers and carefully push in the part sticking out under its own cap.

All glued down. If a part of a cap sticks off the edge just take pliers and carefully push in the part sticking out under its own cap.

14

Repeat steps 11-13 for all coasters

15
Take an extra chipboard square and trace it onto the felt sheet (one for each coaster) then cut them out. (I decided on a different color felt than pictured on the supplies step FYI)

Take an extra chipboard square and trace it onto the felt sheet (one for each coaster) then cut them out. (I decided on a different color felt than pictured on the supplies step FYI)

16
Turn coaster over and place superglue (or hot glue or tacky glue) around edges.  I found that superglue holds the felt the best without making it bumpy.

Turn coaster over and place superglue (or hot glue or tacky glue) around edges. I found that superglue holds the felt the best without making it bumpy.

17
Place felt onto bottom of coaster.

Place felt onto bottom of coaster.

18

Repeat steps 16 and 17 for each coaster

19
Here's where a lot of the optional supplies come into play. I painted a small crate and added a satin finish. Then I cut a small piece of cardboard for the bottom and covered it with washi tape

Here's where a lot of the optional supplies come into play. I painted a small crate and added a satin finish. Then I cut a small piece of cardboard for the bottom and covered it with washi tape

20
All the coasters

All the coasters

21
Coaster set ready to be given as a gift

Coaster set ready to be given as a gift

keyboard shortcuts:     previous step     next step
Comments
1 COMMENT
View More Comments