How to Make a Skateboard Ring

I will teach you how to make a skateboard step-by-step

342 Views 14 Likes
How to Make a Skateboard Ring
30 Steps
Supplies
Embed
1
You will need 6 to 7 Veneers,  container of tight bond three glue, and one clamp

You will need 6 to 7 Veneers, container of tight bond three glue, and one clamp

2
Put glue or veneer and spread evenly

Put glue or veneer and spread evenly

Recommended For You
3
And put glue on the bottom veneer and then the one that goes on top of that

And put glue on the bottom veneer and then the one that goes on top of that

4
line the veneers  them up

line the veneers them up

5
Then continue the steps until you are finished

Then continue the steps until you are finished

6
I gently push veneers together to flatten them

I gently push veneers together to flatten them

7
Place one side equal to each other making sure that it's flat on one side

Place one side equal to each other making sure that it's flat on one side

8
wash the glue off your hands

wash the glue off your hands

9
Lift clamp so you can put Veneers in

Lift clamp so you can put Veneers in

10
Put down clamp on Veneers

Put down clamp on Veneers

11
Make sure veneers are in centre of crap

Make sure veneers are in centre of crap

12
Tighten the clamp tell you can't tighten anymore Then leave for six or more hours

Tighten the clamp tell you can't tighten anymore Then leave for six or more hours

13
Take the veneers out of the clamp.

Take the veneers out of the clamp.

14
Then you need to cut a whole out of the veneers.

Then you need to cut a whole out of the veneers.

15
Then you need to put the peace in the jig. Then take a clamp and clamp the jig to the table.

Then you need to put the peace in the jig. Then take a clamp and clamp the jig to the table.

16
Then cut the veers

Then cut the veers

17
Put your fingers on the top part of the blame and put blade  against the Jig.

Put your fingers on the top part of the blame and put blade against the Jig.

18
Continue till it something close to round

Continue till it something close to round

19
Then use the Dremel to Sand with 60 grit sandpaper till it is round.

Then use the Dremel to Sand with 60 grit sandpaper till it is round.

20
Every once and a while check it and see if you find it it's round enough.

Every once and a while check it and see if you find it it's round enough.

21
Then sand inside ring with 120 Grit sandpaper till smooth.

Then sand inside ring with 120 Grit sandpaper till smooth.

22
This is what it should look like by the end of standing with 60 and 120 grit sandpaper.

This is what it should look like by the end of standing with 60 and 120 grit sandpaper.

23
Then when using the grill stand with 400  sandpaper till smooth.

Then when using the grill stand with 400 sandpaper till smooth.

24
Where gloves and take shop towels put superglue

Where gloves and take shop towels put superglue

25
Keep glue away from face and eyes while it's smoking

Keep glue away from face and eyes while it's smoking

26
This will be a two person job. One person will spend the girl slowly why the other Poston will apply glue

This will be a two person job. One person will spend the girl slowly why the other Poston will apply glue

27
Apply glue on inside of ring and around the edge

Apply glue on inside of ring and around the edge

28
If necessary snd with 400 grid

If necessary snd with 400 grid

29
For the final coat put a nice thick coat

For the final coat put a nice thick coat

30
After school with a drag enjoy wearing your skateboard ring

After school with a drag enjoy wearing your skateboard ring

keyboard shortcuts:     previous step     next step
Comments
0 COMMENTS
View More Comments