How to Make a Giant Ornament Wreath

Here is how I made a huge ornament wreath to hang over my garage!

2.1k Views 209 Likes 1 Comment
How to Make a Giant Ornament Wreath
17 Steps
Supplies
Embed
1
Use thick wire to make a ring a few inches smaller than your hula hoop and attach with shorter wires. Similar to wreath frames in craft stores but much larger! Make sure to make a loop to hang it with

Use thick wire to make a ring a few inches smaller than your hula hoop and attach with shorter wires. Similar to wreath frames in craft stores but much larger! Make sure to make a loop to hang it with

2

This 2nd ring of wire is important. With only a hoop, your ornaments would spin around to the back when you pick up the wreath. The extra wire holds them to the front, saving a TON of time & ornaments

Recommended For You
3
If the tops are loose on your ornaments, you'll need to take them off, add hot glue, and glue them on securely. You need these to secure the ornament to the wire.

If the tops are loose on your ornaments, you'll need to take them off, add hot glue, and glue them on securely. You need these to secure the ornament to the wire.

4
Use the thin wire to attach the largest ornaments to the wire circle. Then use hot glue to attach the ornament to the hula hoop where it touches.

Use the thin wire to attach the largest ornaments to the wire circle. Then use hot glue to attach the ornament to the hula hoop where it touches.

5
Flip the whole thing over (carefully!). Ornaments should not move if well glued. Reinforce with more glue. Wherever an ornament touches wire or hula hoop, add glue.

Flip the whole thing over (carefully!). Ornaments should not move if well glued. Reinforce with more glue. Wherever an ornament touches wire or hula hoop, add glue.

6
Cut a long piece of thin wire (a few feet), wrap one end around the wire hoop or hula hoop, then string ornaments on the wire like beads. Try to alternate colors & sizes as you go.

Cut a long piece of thin wire (a few feet), wrap one end around the wire hoop or hula hoop, then string ornaments on the wire like beads. Try to alternate colors & sizes as you go.

7
Wrap the wire in the direction you want the ornaments to go. I tried to loop mine around the larger ornaments. Find a position you like...

Wrap the wire in the direction you want the ornaments to go. I tried to loop mine around the larger ornaments. Find a position you like...

8
...now arrange each ornament and glue them into place. Start with the ones closest to where you attached the wire to the hoop, and work your way down the string.

...now arrange each ornament and glue them into place. Start with the ones closest to where you attached the wire to the hoop, and work your way down the string.

9
Add more ornaments and keep wrapping & gluing as you go around the largest ornaments.

Add more ornaments and keep wrapping & gluing as you go around the largest ornaments.

10
If you run out of wire, tie it off and start a new piece.

If you run out of wire, tie it off and start a new piece.

11
Here I have all the major spaces covered.

Here I have all the major spaces covered.

12
Gently turn it over again and reinforce all contact points between ornaments with more glue.

Gently turn it over again and reinforce all contact points between ornaments with more glue.

13
Look at it from all angles for bare spots. Especially from the bottom, if you plan to hang it high like I am, because that is the angle it will be viewed. Here I want to cover that yellow hula hoop...

Look at it from all angles for bare spots. Especially from the bottom, if you plan to hang it high like I am, because that is the angle it will be viewed. Here I want to cover that yellow hula hoop...

14
Bare spot filled in with another string of ornaments.

Bare spot filled in with another string of ornaments.

15
Make goofy reflections in the ornaments because all these hot glue fumes are making you crazy...

Make goofy reflections in the ornaments because all these hot glue fumes are making you crazy...

16
Finally, fill in any extra spots by gluing individual ornaments wherever you need. I didn't use wire for this...just lots of glue!

Finally, fill in any extra spots by gluing individual ornaments wherever you need. I didn't use wire for this...just lots of glue!

17
The complete wreath! Ready to hang...but not until the day after Thanksgiving! ;-)

The complete wreath! Ready to hang...but not until the day after Thanksgiving! ;-)

keyboard shortcuts:     previous step     next step
Comments
1 COMMENT
View More Comments